Framing Hammer Milled Face
Framing Hammer Milled Face
Check out this page if you are looking for Framing Hammer Milled Face
 |
 Dead® On Tools DO Ti7® Milled Face TITANIUM PRO Framing Hammer 16oz NEW  US $94.90
|
 Estwing 62941 30oz Framing Hammer Milled Face US $42.86
|
 KC PROFESSIONAL 22 oz FRAMING Hammer Milled Face US $19.99
|
 Estwing 62901 28 Oz Framing Hammer Milled Face US $40.27
|
 Estwing Framing Hammer 22oz Milled Face 14620 US $35.99
|
 Olympia Tool 60 363 24 Ounce Framing Hammer Milled Face US $25.67
|
 Estwing Framing Hammer 24oz Milled Face 14421 US $37.99
|
 New Estwing 28 oz E3 28SM Milled Face Framing Claw Hammer US $25.00
|
 NEW Estwing E3 22SM 22 oz Milled Face Framing Hammer US $33.99
|
 NEW Estwing E3 25SM 25 oz Milled Face Framing Hammer US $37.49
|
 Stiletto 14 Oz Titanium Framing Hammer TiBone TBM14RMS Milled Face US $162.50
|
Planning your aluminium installation - A Handy Checklist
Follow the brief checklist below for a hassle-free installation:
The lightweight advantage of aluminium (34% that of steel) over other architectural materials, makes for ease of handling and fixing with a minimum number of operatives. When handling individual sheets or panels, care should be taken not to damage exposed edges or corners. Thin materials are particularly vulnerable.
Aluminium items have a best and reverse face. Inspect closely and ensure the best face is fixed / positioned on the most visible side.
Material flanges which are oversize must not be forced or hammered into position. Components requiring a reduction in size should ideally be returned to the factory for re-processing.
Site work such as drilling and cutting, should be avoided if at all possible. If specified, items can be supplied as accurately pre-cut and pre-drilled components subject to agreed tolerances
When installing or working unprotected material surfaces, a low tack self adhesive tape or covering is to be applied to prevent surface marking.
When site drilling is unavoidable, standard twist drills are satisfactory for most operations. For deep holes, high speed drills or bits with a steeper point of angle should be used.
Positions for drill holes should not be marked out along visible faces with a scored line. A pencil, or felt tip pen with removable ink or similar is to be used, which can be subsequently wiped off with a soft cloth.
Cutting operations can be effected by semi high-speed and high-speed saws of between 150mm and 450mm diameter, with approximately 3 teeth per 25mm. Band saws and heavy duty woodworking machines are also suitable for light work. Blades used in hand saws should be of high speed type with fairly coarse teeth.
After cutting, it is important that any swarf or chippings are removed from the product surface with extreme care, to avoid the possibility of scratching. These should be removed ideally with an air line or alternatively by lightly brushing away. Burrs can be removed by the use of long angle files with 14 to 20 single cut teeth per 25mm, for most fine work.
Remove any grease, dirt deposits, finger marks, etc, from the material surface with non abrasive cleaning agents and materials, in accordance with the GA maintenance data sheet.
Order Aluminium Products
Easy to specify packages with design flexibility:
- Aluminium Balustrade Panels
- Aluminium Ceiling Panels
- Aluminium Column Casings
- Aluminium Framed Panels
- Aluminium Louvres
- Aluminium Wall Cladding
Order Aluminium Stock Now
Order online with real time availability:
- Aluminium Sheets
- Aluminium Fixing profiles
- Aluminium Mouldings
- Aluminium Angles
- Aluminium Channels
- Aluminium Flat Bars, etc.
And many more aluminium trims and elements.
Visit the site at www.goodingalum.com and order online today.
Gooding Aluminium are a national and international supplier of a wide range of high quality aluminium sheets, aluminium profiles and ‘made to order' aluminium products with ‘invisible' fixing solutions. For more information about bespoke or ready made aluminium products, subscribe by RSS, or by Email or visit our main site at www.goodingalum.com
About the Author
Contact
Gooding Aluminium Limited
1 British Wharf
Landmann Way
London SE14 5RS
United Kingdom
T: + 44 (0)20 8692 2255